基于动力学仿真的6×6轮式越野车辆总体性能评价

为分析和评价某型6×6轮式越野车辆的总体设计性能,建立了整车多刚体动力学模型、刚柔耦合动力学模型以及悬架系统台架试验模型,计算了整车固有特性,依次进行了悬架系统运动学、行驶动力学、操纵稳定性分析。在计算车体和悬架摆臂结构模态的基础上,考核了典型行驶工况下车体和悬架部件结构的动态强度,依据国家相关标准,利用仿真结果对6×6整车设计进行了系统的评价,指出了该越野车总体设计性能的不足,为其进一步改进和优化设计提供了参考依据。研究方法对其他轮式越野车辆系统的设计和评价具有一定的参考价值。     

U型BFRP箍筋试件受剪试验分析

针对U型箍筋抗剪试验缺乏强度折减实践依据的问题,设计15个配有BFRP箍筋的C30混凝土U型试件。在BFRP箍筋两侧用套筒将其锚固,弯折成U型,箍筋两端采用穿心千斤顶施加荷载,逐渐加载至BFRP箍筋破坏。通过分析试验数据,建立试件受力模型,可知弯折部位锚固长度对BFRP箍筋强度折减有较大影响,最大折减为原强度的65%;随着锚固长度的增加,BFRP箍筋强度呈线性增加至某个定值;最后推导出U型BFRP箍筋强度折减公式。     

一种统一的拓扑关系判断模型

拓扑关系是地理信息系统领域中一种非常重要的空间关系。当前已经提出了多种模型来对空间对象间的拓扑关系进行判断,但是这些模型都不能判断那些由点、线、多边形任意组合而成的异构几何集合对象间的拓扑关系。针对当前拓扑关系研究的不足,引入了混合几何的概念和正规化准则,基于此空间对象模型和维扩展9交集模型,提出了一个拓扑关系判断模型—集成型维扩展9交集模型(IDE 9IM),它不但能够判断单一的点、线、面以及同构几何集合对象间的拓扑关系,而且还能从复杂空间对象的总体和局部两个方面对异构几何集合对象间的拓扑关系进行判断,可以作为一个判断任意几何对象间拓扑关系的统一模型。     

Investigation on the process parameters of TIG-welded aluminum alloy through mechanical and microstructural characterization

Multi-pass TIG welding was conducted on plates (15×300×180 mm3) of aluminum alloy Al-5083 that usually serves as the component material in structural applications such as cryogenics and chemical processing industries. Porosity formation and solidification cracking are the most common defects when TIG welding Al-5083 alloy, which is sensitive to the welding heat input. In the experiment, the heat input was varied from 0.89 kJ/mm to 5 kJ/mm designed by the combination of welding torch travel speed and welding current. Tensile, micro-Vicker hardness and Charpy impact tests were executed to witness the impetus response of heat input on the mechanical properties of the joints. Radiographic inspection was performed to assess the joint's quality and welding defects. The results show that all the specimens displayed inferior mechanical properties as compared to the base alloy. It was established that porosity was progressively abridged by the increase of heat input. The results also clinched that the use of me-dium heat input (1-2 kJ/mm) offered the best mechanical properties by eradicating welding defects, in which only about 18.26% of strength was lost. The yield strength of all the welded specimens remained unaffected indicated no influence of heat input. Partially melted zone (PMZ) width also affected by heat input, which became widened with the increase of heat input. The grain size of PMZ was found to be coarser than the respective grain size in the fusion zone. Charpy impact testing revealed that the absorbed energy by low heat input specimen (welded at high speed) was greater than that of high heat input (welded at low speed) because of low porosity and the formation of equiaxed grains which induce better impact toughness. Cryogenic (-196 C) impact testing was also performed and the results corroborate that impact properties under the cryogenic environment revealed no appreciable change after welding at designated heat input. Finally, Macro and micro fractured surfaces of tensile and impact specimens were analyzed using Stereo and Scanning Electron Microscopy (SEM), which have supported the experimental findings.     

英语口语中情态动词和助词的重读

文章主要讨论的是在一般肯定句中情态助词何时及如何被重读的 ,介绍了句子的意思和重读之间的关系 ,以及在否定句和疑问句中基本助词的重读问题。     

三维声音处理技术的研究

在声音定位原理研究的实验中,运用软件编程的方法改变原有．WAV文件(单声道、16位)的数据存储格式为有空间感立体声的．WAV声音文件(双声道、16位),在变换过程中加入了ITD、IID的数学模型,效果令人满意,听者能明显感到随着声源位置信息的改变,声源位置、音量也在改变     

随机-非概率模型下的船体结构屈服强度可靠性分析

针对在役舰船船体载荷、材料属性的随机特性和实船勘验得出的腐蚀损伤下船体抗力区间特性,提出一种基于随机概率理论和区间非概率理论的随机-非概率可靠性分析模型,分别从区间变量随机化和随机变量区间化两个角度给出该模型的可靠性指标求解方法。基于该模型对某舰船船体结构屈服强度进行可靠性分析,结果表明:该模型既体现了结构变量的客观不确定性又减弱了评估结果的盲目保守性,对于既含有随机变量又含有区间变量的在役舰船的可靠性评估具有很强的适用性。     

等离子体天线辐射特性研究

用环形荧光灯制作了两幅等离子体天线,等离子体激励源分别为220 V交流电压和射频信号.测量了两种等离子体天线的电压驻波比和远区辐射场强,并与周长相同的方框金属天线的特性进行了对比.结果表明,等离子体天线的增益较金属天线平均低5 dB左右;在试验频率低端,220 V电源预激励方式下等离子体天线增益比RF直接激励要高2～4 dB,随着频率增加,两者增益差变小.     

驱护舰指挥关系的时效和质量熵分析方法

为了解决如何对驱护舰指挥关系的优化进行定量分析,首先定性分析了新应用的方面指挥模式,继而以指挥组织结构的时效性和准确性为测评指标,建立了基于熵理论的优化分析数学模型,并对现有的两种指挥关系进行了定量计算分析,得到了与定性分析相一致的结论.该方法能在定性分析的基础上定量地研究驱护舰指挥关系的优劣,为定性分析提供有力的数据支持,对驱护舰指挥关系的优化分析具有参考价值.     

内置式耐压液舱实肋板拓扑优化设计方案分析

通过对内置式耐压液舱中实肋板开孔拓扑优化设计后的强度和稳定性分析发现，对于周向范围为162°的内置式耐压液舱，实肋板在中内龙骨附近开孔较优。实肋板开孔后对于其本身的稳定性影响不大，但MISES应力会有所变化；实肋板开孔后，液舱结构的稳定性会稍微降低，后期在进行液舱结构设计时要考虑是否加强。